A50 A50 UltraClear Sound Shaping Expandable Cordless TelephoneInstallation Guide & User ManualCongratulations… You have just purchased theMost Rem
10requires a modular phone jack (RJ11C) and a standard 120V AC wall outlet. Place this telephone on a stable surface. Serious damage and/or injury may
11Installing Batteries Handset batteries MUST be connected before beginning initial charging!(Diagram #6) – Installing the batteries1. Remove battery
12Battery LifeFully charged batteries provide an average talk time of about 4 hours, or standby time of about 8 days. Talk time & standby time may
13Area Code SettingYour BellSouth A50 allows you to dial from your CALLER ID memory and your phonebook. When you use your phone for the rst time or i
141. Press the “SEL” button once then the LCD display will show PROGRAM to indicate you entered the SETTING MODE. 2. Press the 4 key, then the SE
15Caution: When the “AUTO AMPLIFY” switch is set to ON, the handset volume will be set to loud. To protect people who do not experience a heari
16ference. To improve reception, move closer to the base. Once the handset is too far away from the base, an out of range warning tone will be sound
17Basic A50 OperationAnswering A Call1. If the handset is off of the base, press the button to receive the call. -Or- 1. If the handset is in th
18Using The Pause Feature For DialingThe “R/P” button is used to insert a temporary pause during a dialing sequence. Program-ming in a pause will ca
19NOTE: When you plug the headset into the HEADSET JACK, it automatically mutes the microphone and speaker of the cordless handset. Unplug
2Thank you for selecting the A50 UltraClear Sound Shaping Ex-pandable Cordless Telephone from BellSouth. This manual will help you install your teleph
20-Or-Save numbers and names from the CALLER ID to phone book1. Begin with the phone in the standby mode, press the or arrow button repeatedly t
21Deleting all records from phone book1. In standby mode, press the “MEMO” button, and then the LCD shows the total number of records. 2. Press the
22Deleting a single CALLER ID number1. In standby mode, press the or arrow button, then the LCD display shows the total number of CALLER ID
23Technical informationThis cordless telephone uses radio frequencies to allow mobility. There are certain dif-culties in using radio frequenc
24Maintenance and CareThe BellSouth A50 has been designed to give you years of dependable service. To ensure the utmost in performance, follow these g
25Dimensions:Handset Size: 6” X 2.25” X 1”Base Size: 5.5” X 4” X 2.5” Weight: 11.2 oz with batteriesPower Requirements:120VAC-60Hz-18W / 12VDC-50
263. If the phone does not ring when you receive a call:· Make sure the handset ringer is ON.· Make sure the telephone modular line cord is connect
27FCC Registration NoticeTHE INFORMATION INFORMING THE USER OF HIS/HER AND THE TELEPHONE COMPANY’S RIGHT AND OBLIGATION IS OUTLINED BELOW. a
28otherwise do not alter or repair any part of device except as specified.i) Connection to party line service is subject to state tariffs. Contact t
29Warranty & ServiceHITEC Group, Ltd. warrants the BellSouth A50 against any defect in materials or workmanship for the period of one year from
3Table Of ContentsCONDITIONS FOR USE Page 5FEATURES & FUNCTIONS Base Unit Top & Bottom Views Page 6 Handset Front View
4Table Of ContentsBasic Operation Answering a call Page 17 Making a call Page 17 Using the Pre-dialing feature Page 17 Usi
5Conditions for UseImportant Safety InstructionsRead and understand the Installation Guide & User Manual. When using your telephone equipment, bas
6Features & Functions1. Page icon button (PAGE): Press to page the handset. The handset will ring for about 25 seconds then end the paging a
7Features & Functions6. Lighted keypad: The keypad stays lit up for 15 seconds after removing the hand-set from the base. To reactivate the fea
8Back View Left View Right View(Diagram #3) – Location of Back & Sides of Handset ControlsFeatures & Functions1234561. B
9Features & FunctionsERROR message: The CALLER ID display is unable to identify the caller’s name and/or number. The LCD will show ERROR, this do
Kommentare zu diesen Handbüchern